ite compliant led signal modules designed in the u.s.a meets buy american provision under the american recovery and reinvestment act 2009 for projects requiring buy american provision certification, consult factory for additional information and special ordering details
www.dialight.com all led ball signal modules (8 inch (200mm) and 12 inch (300mm) shall be fully compliant to the ite vtcsh led circular supplement specifications dated and adopted june 27, 2005. compliance to the ite vtcsh-2 interim purchase specification is not sufficient, and will not substitute for compliance to the ite vtcsh led circular supplement specifications. additionally, prior to bid award, the manufacturer shall submit to purchaser, reports from etl/intertek, that certify full compliance of all led ball signal modules to the entire ite specification. these tests should include but not be limited to the luminous intensity measurements and requirements outlined in the ite specification sections 6.4.4 through 6.4.4.4.2 (25c and 74c / 49c). evidence of full compliance to all required testing methods, procedures and sections as outlined in the above ite document figure 2, design qualification testing flow chart must be included without any exceptions, changes or omissions. the manufacturer must also submit a data sheet showing the exact catalog number of the items submitted on the bid and the independent lab report must show full qualification of this catalog number. to ensure optimal quality of illumination; uniformity; reliability; and appearance, all ball traffic signal modules shall utilize hi-flux leds rated at 1-watt or higher, as their source of illumination. to ensure competency of design and manufacturing, manufacturers of ball, arrow, and pedestrian signal modules shall have a minimum of 7 years of experience in utilizing hi-flux leds rated at 1-watt or higher, as the source of illumination in their ball traffic signal modules. additionally, manufacturers must have utilized in excess of 20 million hi-flux leds in their led traffic signal modules during the most recent 10 year period. all led 12 inch (300 mm) arrow signal modules shall be fully compliant to the omni-directional specifications of the ite vtcsh - led vehicle arrow traffic signal supplement adopted july 1, 2007. additionally, prior to bid award, the manufacturer shall submit to purchaser, reports from etl/intertek that certify full compl iance of all led arrow signal modules. these tests should include but not be limited to the luminous intensity measurements and requirements outlined in the ite specification sections 6.4.4 through 6.4.4.4.2 (25c and 74c / 49c). evidence of full compliance to all required testing methods, procedure s and sections as outlined in the above ite document attachment 1, design qualification testing flow chart must be included without any excepti ons, changes or omissions the manufacturer must also submit a data sheet showing the exact catalog number of the items submitted on the bid and the independent lab report must show full qualification of this catalog number. all led 16x18 countdown pedestrian signal modules shall be fully compliant to the ite ptcsi part-2: led pedestrian traffic sig nal modules specifications adopted august 4, 2010 or the latest adopted version as listed on the ite website at time of bid. additionally, prior to bid award, the manufacturer shall submit to purchaser, repo rts from etl/intertek that certify full compliance of led signal modules, to these specifications. evidence of full compliance to all required testing methods, pr ocedures and sections as outlined in the above ite document attachment 2, design qualification testing flow chart must be included without any excepti ons, changes or omissions. the manufacturer must also submit a data sheet showing the exact catalog number of the items submitted on the bid an d the independent lab report must show full qualification of this catalog number. combination hand/person pedestrian signal modules shall incorpo rate separate power supplies for the hand and the person icons. in addition to, and in excess of the above applicable ite specification compliance, the on-board circuitry of all led traffic s ignal modules shall include voltage surge protection, to withstand high-repetition noise transients and low-repetition high-energy transients as stated in section 2.1.8, nema standard ts 2-2003. in addition, the module shall comply with the following standards: iec 1000-4-5 at 3kv with a 2 ohm source impedan ce, ansi/ieee c62, 41-2002; iec 61000-4-12 (6kv, 200a, 100khz ring wave). warranty: manufacturer shall provide at time of bid, a written warranty which provides for repair or replacement of modules that fail to function as intended due to workmanship or material defects within the first 60 months from date of delivery. modules which exhibit luminous intensities l ess than the minimum as specified in the ite specifications as indicated above, within the first 60 months from date of delivery shall be replaced or r epaired. notes: csa approved to the following applicable requirements: csa standard c22.2 no. 9.0-96 general requirements for luminaires csa std. no. c22.2 no. 250.0-04 luminaires ul std. no. 1598-2004 (may 2006) luminaires ite compliant led traffic signal module performance specifications designed in the u.s.a meets buy american provision under the american recovery and reinvestment act 2009 for projects requiring buy american provision certification, consult factory for additional information and special ordering details
p * fully compliant to ite vtcsh-led vehicle arrow supplement dated 7/01/2007 p allows for mounting in any orientation in the signal head p industrys lowest power for all colors p meets or exceeds ite intensity, color and uniformity specification, including 49oc / 74oc requirements p temperature compensated power supplies for longer led life p uniform appearance p transient suppression exceeds ite and nema specifications (up to 6kv ring wave) p manufactured with anti-capillary wires p conformal coated power supply p secondary lens treatment for abrasion resistance p intertek/etl certified and listed on etl certification program p all units operate at 80-135vac rms, 603hz p *fully compliant to ite vtcsh-led circular signal supplement dated 6/27/2005 p industrys lowest power for all colors p meets or exceeds ite intensity, color and uniformity specification, including 49oc / 74oc requirements p temperature compensated power supplies for longer led life p uniform appearance p expanded view radiation pattern suitable for span wire and steep grade applications p transient suppression exceeds ite and nema specifications (up to 6kv ring wave) p manufactured with anti-capillary wires p conformal coated power supply p secondary lens treatment for abrasion resistance p patent no. 7,281,818 and other patents pending p intertek/etl certified and listed on etl certification program p all units operate at 80-135vac rms, 603hz uniform appearance led traffic signal modules omni-directional, uniform appearance led arrows www.dialight.com part number color lens type dominant wavelength (nm) typical wattage at 25 c peak minimum maintained luminous intensity (cd) *meets ite vtcsh led circular signal supplement csa approved size (in) 433-1110-003xl red tinted 625 6 165 a a 8 433-1170-003xl red clear 625 6 165 a a 8 433-3130-901xl yellow tinted 590 7 410 a a 8 433-3170-901xl yellow clear 590 7 410 a a 8 433-2120-001xl green tinted 500 8 215 a a 8 433-2170-001xl green clear 500 8 215 a a 8 433-1210-003xl red tinted 625 6 365 a a 12 433-1270-003xl red clear 625 6 365 a a 12 433-3230-901xl yellow tinted 590 12 910 a a 12 433-3270-901xl yellow clear 590 12 910 a a 12 433-2220-001xl green tinted 500 7 475 a a 12 433-2270-001xl green clear 500 7 475 a a 12 part number color lens type typical wattage at 25oc dominant wavelength (nm) peak minimum maintained luminous intensity (cd) *meets ite spec csa approved 432-1314-001xod red tinted 6 628 56.8 a a 432-1374-001xod red clear 6 628 56.8 a a 431-3334-901xod yellow tinted 6 590 141.6 a a 431-3374-901XOD yellow clear 6 590 141.6 a a 432-2324-001xod green tinted 6 500 73.9 a a 432-2374-001xod green clear 6 500 73.9 a a
part number size description typical wattage @ 25 o c min. luminance (cd/m 2 ) *meets ite spec csa approved hand person hand person 430-6450-001x 16 x 18 side-by-side hand and person 8 7 1,400 2,200 aa 430-6472-001x 16 x 18 overlay hand and person 8 6 1,400 2,200 aa 430-5770-001x 12 x 12 hand only 8 n/a 1,400 n/a aa 430-7771-001x 12 x 12 person only n/a 7 n/a 2,200 aa 430-6772-001x 12 x 12 overlay hand and person 8 6 1,400 2,200 aa 430-5570-001x 9 x 9 hand only 6 n/a 1,400 n/a a 430-7570-001x 9 x 9 person only n/a 6 n/a 2,200 a p * fully compliant to ite ptcsi part 2 led pedestrial traffic signal module specification adopted 3/9/04 p meets / exceeds ite uniformity ratio of not more than 1 to 5 between the max and min luminance values as measured in (.5) dia spots p manufactured with anti-capillary wires p conformal coated power supply p fuse and transient suppressor incorporated for superior line and load protection p independent dedicated power supplies for added safty and reliability p intertek/etl certified and listed on etl certification program p transient suppression exceeds ite and nema specifications (up to 6kv ring wave) p all units operate at 80-135vac rms, 603hz uniform appearance hand and person pedestrian signals p * f ully compliant to ite ptcsi part 2 led pedestrial traffic signal module specification adopted 8/04/2010 p mutcd compliant for coundown applications p full preemption compatibility p up to 8 units can be connected in parallel without affecting of the monitoring of the hand/person p manufactured with anti-capillary wires p three (3) independent dedicated power supplies for added safty and reliability p intertek/etl certified and listed on etl certification program p reduced off state icon visibility results in increased pedestrian safety by eliminating the potential to misinterpret the signal p conformal coated power supply p new improved one piece housing design p improved optical design to provide superior uniform appearance of the icons p transient suppression exceeds ite and nema specifications (up to 6kv ring wave) p all units operate at 80-135vac rms, 603hz uniform appearance countdown pedestrian signals special applications : upon customer request, above units are available with option to countdown the clearance mode and the walk mode. add suffix w to above part numbers. important note: mutcd does not recommend the use of a countdown timer in the walk mode www.dialight.com part number housing size symbol color typical wattage @ 25oc min. luminance (cd/m2) *meets ite spec csa approved countdown hand person countdown hand person countdown hand person 430-6479-001x 16 x 18 portland orange portland orange lunar white 8 11 10 1,400 1,400 2,200 a a 430-7773-001x 12 x 12 portland orange n/a n/a 5 n/a n/a 1,400 n/a n/a a dialight reserves the right to make changes at any time in order to supply the best product possible. the most current version of this document will always be available at: www.dialight.com/assets/brochures_and_catalogs/signaling/ite_spec_brochure.pdf ite_spec_brochure_l
|
